| After-sales Service: | 12 Months |
|---|---|
| Type: | Balance Roller Straightening Machine, Balance Roller Straightening Machine |
| Voltage: | 380V, 380V |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
This Compact Press Feeding Systems, which is famous used for multi solutions of making automotive and motorcycle parts in engine, chassis and blanking sheets etc.
NCHF automatic medium metal sheet 3 in 1 uncoiling straightener servo feeder applicable material:
Coil thickness (mm): 0.3-3.2
Coil width (mm): 50-1500
Coil weight (kg): 3000-15000
Coil inner diameter (mm): ø470-ø530
Max feeding speed (m/min): 20
This Compact Press Feeding Systems, which is famous used for multi solutions of making automotive and motorcycle parts in engine, chassis and blanking sheets etc.
1. The loosening part of the leveling roller of the three in one sheet feeder of the press is completed by the air cylinder. It is suitable for the stamping, leveling and feeding of sheet coils with material thickness of 0.3mm ~ 3.2mm and with of 50mm ~ 1500mm. The upper leveling is equipped with arc adjusting wheel to adjust the ideal arc.
2. The main shaft of the material rack adopts the oil pressure expansion system, the material roll drum adopts the wedge-shaped slider or the top material block connecting rod structure, and the width of the material roll is adjusted by the screw of the material retaining roll. When discharging, the large cylinder lifts the outer material retaining roll to avoid the material, which is convenient for material loading and unloading. It has high reliability, low labor intensity and good safety. It is equipped with a pressing arm so that the material will not be loose. The opposite photoelectric induction system is used for discharging, and the material is discharged automatically, At the same time, the pneumatic support arm is used to lift the material to control the radian of the material and make the feeding smooth.
3. The power roller is used to send the material head to the leveling machine.
4. The leveling is adjusted by the worm wheel and worm. The worm wheel is driven by the worm wheel rotated by the hand wheel to drive the upper sliding block to rise and fall. There is a scale adjustment amount on the adjusting wheel.
5. The leveling and relaxation adopts the eccentric structure and is realized by the cylinder. During leveling, the cylinder is ventilated, and the upper slider is driven and pressed down by the cylinder piston. During relaxation, the cylinder is relaxed by the lifting slider. When loosening, a high-speed exhaust valve is installed in the exhaust pipeline, so the relaxation speed is faster.
6. The height of the material line is automatically raised and lowered by electric belt worm gear, which matches the height of the product mold, and the adjustment is convenient, labor-saving and reliable.
Standard configuration:
Touch screen HMI operation
Photoelectric arc control system
Feed outlet guide frame device
Automatic height adjustment device of feeding line
Overhead disc brake
Material roll head flattening device
Support arm Press arm Retaining arm device
Arc control roller
Variable frequency speed regulation of rack motor
Rack oil pressure expansion connecting rod type / wedge type
Main shaft support arm of material rack (material weight ≤ 10t)
Compact Press Feeding Systems technical parameters:
|
Model |
NCHF-400 |
NCHF-500 |
NCHF-600 |
NCHF-800 |
NCHF-1000 |
NCHF-1300 |
NCHF-1500 |
|
Material Width (mm) |
100~400 |
100~500 |
100~600 |
100~800 |
100~1000 |
100~1300 |
100~1500 |
|
Material Thinkness (mm) |
0.3-4.5 |
||||||
|
Weight of Material loading (KG) |
3000 |
5000 |
8000-10000 | 15000 | |||
|
Coil inner diameter (mm) |
ø470-ø530 |
||||||
|
Coil outer diameter (mm) |
ø1400 |
||||||
|
Max speed (m/min) |
18 |
||||||
|
Straightening roller (mm) |
Upper 4, lower 3 |
||||||
|
Feeding roller (set) |
1 |
||||||
|
Feeding height (mm) |
1200±100 |
||||||
|
Voltage |
220V AC 50HZ/380V AC 50HZ |
||||||
|
Air pressure (kgf/cm2) |
5 |
||||||
|
Material rack expansion mode |
Oil pressure |
||||||
|
Machine dimensions (m) |
4.8*2.3* |
4.8*2.3* |
4.8*2.3* |
4.8*2.3* |
4.8*2.3* |
4.8*2.3* |
4.8*2.3* |
Material straightening capacity:
| Model | Material Thickness [mm] | ||||||||
|
0.3-0.8 |
1.0 |
1.6 |
2.3 |
2.5 |
2.8 |
3.2 |
4.5 |
||
| Material Width [mm] |
NCHF-400 |
400 |
370 |
300 |
160 |
||||
|
NCHF-500 |
500 |
320 |
270 |
160 |
|||||
|
NCHF-600 |
600 |
360 |
290 |
250 |
160 |
||||
|
NCHF-800 |
800 |
480 |
320 |
250 |
220 |
150 |
|||
|
NCHF-1000 |
1000 |
450 |
290 |
230 |
200 |
110 |
|||
|
NCHF-1300 |
1300 |
420 |
280 |
220 |
200 |
100 |
|||
|
NCHF-1500 |
1500 |
400 |
260 |
215 |
190 |
100 |
|||
Industry information
What is the difference between two in one straightener and three in one feeder?
In today's stamping industry, with the continuous increase of labor cost and difficult recruitment, the soaring of raw materials and the improvement of stamping process requirements, resulting in the increase of stamping industry cost, which requires stamping enterprises to reduce the increase of labor cost, reduce the waste of raw materials and improve the product qualification rate. So how to distinguish the three in one feeder and the two in one leveling machine?
The three in one feeder and the two in one straightener are the two most used automatic models in the stamping industry. The appearance and structure of the two models are very similar, especially for the thin plate and thick plate models. However, when customers make inquiries about the two models, they find that there are great differences. Therefore, many customers have doubts. Why are the prices of the two models so different? That is because although the two models are similar in appearance, they are very different in function, structure and operation.
1. Structural differences.
The material rack of the two in one straightener can be powered or unpowered. The pressing arm is not equipped with another drive motor. The induction is usually induced by an induction frame. The transmission of the leveler is driven by a motor and a reducer. The whole machine does not have the function of up and down lifting. The three in one feeder racks are all powered. The pressing arm is equipped with a drive motor. The induction is two groups of opposed photoelectricity, which can automatically control the speed. The leveling feeder head is driven by an imported servo motor. The whole machine is equipped with an electric lifting adjustment device.
2. Differences in operation and use.
The three in one feeder is blocked and limited by the blocking arm, which can realize the fully automatic material introduction and feeding process in combination with the pressing arm, supporting arm and folding arm. The precise handwheel micro adjustment mode has high adjustment accuracy, and the electric control operation adopts a seven-inch touch screen. The 2-in-1 leveler needs to manually position the retaining A-type iron, adjust the introduction, feeding and material thickness, and adjust repeatedly. The electric control operation adopts the button operation mode of the electric control box, which is not highly integrated.
3. Functional differences.
The two in one leveler is the abbreviation of the two in one material rack and leveler. It has the functions of uncoiling and leveling the material coil but does not have the feeding function. A few meters of waiting area should be reserved at the discharge port. It can be used with a punch only when it is equipped with roller feeders, NC feeders and other feeders. It occupies a large space. The three in one feeder is the abbreviation of the three in one material rack leveling feeder. It has the three functions of uncoiling, leveling and feeding of the material coil, and can be directly matched with the punch without reserving the waiting area. It occupies a small space.
In today's stamping industry, with the continuous increase of labor cost and difficult recruitment, the soaring of raw materials and the improvement of stamping process requirements, resulting in the increase of stamping industry cost, which requires stamping enterprises to reduce the increase of labor cost, reduce the waste of raw materials and improve the product qualification rate. So how to distinguish the three in one feeder and the two in one straightener machine?
The three in one feeder and the two in one straightener are the two most used automatic models in the stamping industry. The appearance and structure of the two models are very similar, especially for the thin plate and thick plate models. However, when customers make inquiries about the two models, they find that there are great differences. Therefore, many customers have doubts. Why are the prices of the two models so different? That is because although the two models are similar in appearance, they are very different in function, structure, and operation.
1. Structural differences.
The material rack of the two in one leveler can be powered or unpowered. The pressing arm is not equipped with another drive motor. The induction is usually induced by an induction frame. The transmission of the leveler is driven by a motor and a reducer. The whole machine does not have the function of up and down lifting. The three in one feeder racks are all powered. The pressing arm is equipped with a drive motor. The induction is two groups of opposed photoelectricity, which can automatically control the speed. The leveling feeder head is driven by an imported servo motor. The whole machine is equipped with an electric lifting adjustment device.
2. Differences in operation and use.
The three in one feeder is blocked and limited by the blocking arm, which can realize the fully automatic material introduction and feeding process in combination with the pressing arm, supporting arm and folding arm. The precise handwheel micro adjustment mode has high adjustment accuracy, and the electric control operation adopts a seven-inch touch screen. The 2-in-1 leveler needs to manually position the retaining A-type iron, adjust the introduction, feeding and material thickness, and adjust repeatedly. The electric control operation adopts the button operation mode of the electric control box, which is not highly integrated.
3. Functional differences.
The two in one straightener is the abbreviation of the two in one material rack and leveler. It has the functions of uncoiling and leveling the material coil but does not have the feeding function. A few meters of waiting area should be reserved at the discharge port. It can be
Hot Tags: compact press feeding systems, China, manufacturers, factory, 3 in 1 Compact Feed Line, Cut To Length Coil Lines, Air Feeder, Uncoiler Straightener Feeder Machine, Automatic Coil Feed Line, Compact Coil Feed Line
){kind=link}